♥♥ 2018 NEW RECOMMEND ♥♥

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 100-105 Exam Dumps (PDF & VCE):
Available on: https://www.exambible.com/100-105-exam/

Cause all that matters here is passing the Cisco 100-105 exam. Cause all that you need is a high score of 100-105 Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) exam. The only one thing you need to do is downloading Exambible 100-105 exam study guides now. We will not let you down with our money-back guarantee.

2017 Mar 100-105 answers

Q81. - (Topic 7) 

Which device allows users to connect to the network using a single or double radio? 

A. access point 

B. switch 

C. wireless controller 

D. firewall 

Answer:


Q82. DRAG DROP - (Topic 1) 

On the left are various network protocols. On the right are the layers of the TCP/IP model. Assuming a reliable connection is required, move the protocols on the left to the TCP/IP layers on the right to show the proper encapsulation for an email message sent by a host on a LAN. (Not all options are used.) 

Answer: 


Q83. - (Topic 7) 

Which statement about native VLAN traffic is true? 

A. Cisco Discovery Protocol traffic travels on the native VLAN by default 

B. Traffic on the native VLAN is tagged with 1 by default 

C. Control plane traffic is blocked on the native VLAN. 

D. The native VLAN is typically disabled for security reasons 

Answer:


Q84. - (Topic 7) 

On which type of device is every port in the same collision domain? 

A. a router B. a Layer 2 switch 

C. a hub 

Answer:

Explanation: Collision domainA collision domain is, as the name implies, a part of a network where packet collisions can occur. A collision occurs when two devices send a packet at the same time on the shared network segment. The packets collide and both devices must send the packets again, which reduces network efficiency. Collisions are often in a hub environment, because each port on a hub is in the same collision domain. By contrast, each port on a bridge, a switch or a router is in a separate collision domain. 


Q85. - (Topic 1) 

Refer to the exhibit. 

If host A sends an IP packet to host B, what will the source physical address be in the frame when it reaches host B? 

A. 10.168.10.99 

B. 10.168.11.88 

C. A1:A1:A1:A1:A1:A1 

D. B2:B2:B2:B2:B2:B2 

E. C3:C3:C3:C3:C3:C3 

F. D4:D4:D4:D4:D4:D4 

Answer:

Explanation: 

When packets transfer from one host to another across a routed segment, the source IP address always remains the same source IP address, and the source physical (MAC) address will be the existing router’s interface address. Similarly, the destination IP address always remains the same and the destination physical (MAC) address is the destination router’s interface address. 


Far out 100-105 practice test:

Q86. - (Topic 5) 

Select three options which are security issues with the current configuration of SwitchA. (Choose three.) 

A. Privilege mode is protected with an unencrypted password 

B. Inappropriate wording in banner message 

C. Virtual terminal lines are protected only by a password requirement 

D. Both the username and password are weak 

E. Telnet connections can be used to remotely manage the switch 

F. Cisco user will be granted privilege level 15 by default 

Answer: A,B,D 


Q87. - (Topic 3) 

Refer to the exhibit. 

The internetwork is using subnets of the address 192.168.1.0 with a subnet mask of 

255.255.255.224. The routing protocol in use is RIP version 1. Which address could be assigned to the FastEthernet interface on RouterA? 

A. 192.168.1.31 

B. 192.168.1.64 

C. 192.168.1.127 

D. 192.168.1.190 

E. 192.168.1.192 

Answer:

Explanation: 

Subnet mask 255.255.255.224 with CIDR of /27 which results in 32 hosts per. 

192.168.1.31 is the broadcast address for sunbet '0' 

192.168.1.64 is the network address for subnet '2' 

192.168.1.127 is the broadcast address for subnet '3' 

192.168.1.192 is the network address for subnet '6' 


Q88. DRAG DROP - (Topic 4) 

Move the protocol or service on the left to a situation on the right where it would be used. (Not all options are used.) 

Answer: 


Q89. - (Topic 3) 

ROUTER# show ip route 

192.168.12.0/24 is variably subnetted, 9 subnets, 3 masks C 192.168.12.64 /28 is directly connected, Loopback1 C 192.168.12.32 /28 is directly connected, Ethernet0 C 192.168.12.48 /28 is directly connected, Loopback0 O 192.168.12.236 /30 [110/128] via 192.168.12.233, 00:35:36, Serial0 C 192.168.12.232 /30 is directly connected, Serial0 O 192.168.12.245 /30 [110/782] via 192.168.12.233, 00:35:36, Serial0 O 192.168.12.240 /30 [110/128] via 192.168.12.233, 00:35:36, Serial0 O 192.168.12.253 /30 [110/782] via 192.168.12.233, 00:35:37, Serial0 O 192.168.12.249 /30 [110/782] via 192.168.12.233, 00:35:37, Serial0 O 192.168.12.240/30 [110/128] via 192.168.12.233, 00:35:36, Serial 0 

To what does the 128 refer to in the router output above? 

A. OSPF cost 

B. OSPF priority 

C. OSPF hop count 

D. OSPF ID number 

E. OSPF administrative distance 

Answer:

Explanation: 

The first parameter is the Administrative Distance of OSPF (110) while the second parameter is the cost of OSPF. 


Q90. CORRECT TEXT - (Topic 6) 

There are three locations in a school district of a large city: ROUTER -M, ROUTER -W and ROUTER -U. The network connection between two of these locations has already functioned. Configure the ROUTER -M router IP addresses on the E0 and S0 interfaces so that the E0 receives the first usable subnet while the S0 receives the second usable subnet from the network 192.168.160.0/28. Both interfaces would receive the last available ip address on the proper subnet. 

NotE. The OSPF process must be configured to allow interfaces in specific subnets to participate in the routing process. 

Answer: ROUTER-M> enable PassworD. Cisco ROUTER-M# config t ROUTER-M(config)# interface e0 ROUTER-M(config-if)# ip address 192.168.160.14 255.255.255.240 

ROUTER-M(config-if)# no shutdown ROUTER -M(config-if)# exit ROUTER -M(config)# interface s0 ROUTER-M(config-if)# ip address 192.168.160.30 255.255.255.240 ROUTER-M(config-if)# no shutdown ROUTER-M(config-if)# end ROUTER-M# copy run start