Examcollection ccna 200 125 Questions are updated and all 200 125 cisco answers are verified by experts. Once you have completely prepared with our cisco ccna 200 125 exam prep kits you will be ready for the real ccna 200 125 study guide exam without a problem. We have Up to the minute Cisco 200 125 ccna pdf dumps study guide. PASSED 200 125 ccna pdf First attempt! Here What I Did.
P.S. Actual 200-125 preparation exams are available on Google Drive, GET MORE: https://drive.google.com/open?id=1qSmqe9lmg23sR5XECqlhobCqcIIdpdHn
New Cisco 200-125 Exam Dumps Collection (Question 15 - Question 24)
Q1. Refer to the exhibit.
A technician has installed SwitchB and needs to configure it for remote access from the management workstation connected to SwitchA. Which set of commands is required to accomplish this task?
A. SwitchB(config)# interface FastEthernet 0/1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown
B. SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# ip default-gateway 192.168.8.254 255.255.255.0 SwitchB(config-if)# no shutdown
C. SwitchB(config)# ip default-gateway 192.168.8.254 SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown
D. SwitchB(config)# ip default-network 192.168.8.254 SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown
E. SwitchB(config)# ip route 192.168.8.254 255.255.255.0 SwitchB(config)# interface FastEthernet 0/1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown
Answer: C
Explanation:
To remote access to SwitchB, it must have a management IP address on a VLAN on that
switch. Traditionally, we often use VLAN 1 as the management VLAN (but in fact it is not secure).
In the exhibit, we can recognize that the Management Workstation is in a different subnet from the SwitchB. For intersubnetwork communication to occur, you must configure at least one default gateway. This default gateway is used to forward traffic originating from the switch only, not to forward traffic sent by devices connected to the switch.
Q2. Which two benefits are provided by creating VLANs? (Choose two.)
A. added security
B. dedicated bandwidth
C. provides segmentation
D. allows switches to route traffic between subinterfaces
E. contains collisions
Answer: A,C
Explanation:
AVLAN is a switched network that is logically segmented on an organizational basis, by
functions, project teams, or applications rather than on a physical or geographical basis. Security:
VLANs also improve security by isolating groups. High-security users can be grouped into a VLAN, possible on the same physical segment, and no users outside that VLAN can communicate with them.
LAN Segmentation
VLANs allow logical network topologies to overlay the physical switched infrastructure such that any arbitrary collection of LAN ports can be combined into an autonomous user group or community of interest. The technology logically segments the network into separate Layer 2 broadcast domains whereby packets are switched between ports designated to be within the same VLAN. By containing traffic originating on a particular LAN only to other LANs in the same VLAN, switched virtual networks avoid wasting bandwidth.
Q3. Why will a switch never learn a broadcast address?
A. Broadcasts only use network layer addressing.
B. A broadcast frame is never forwarded by a switch.
C. A broadcast address will never be the source address of a frame.
D. Broadcast addresses use an incorrect format for the switching table.
E. Broadcast frames are never sent to switches.
Answer: C
Explanation:
Switches dynamically learn MAC addresses based on the source MAC addresses that it sees, and since a broadcast is never the source, it will never learn the broadcast address.
Q4. Which three elements must be used when you configure a router interface for VLAN trunking? (Choose three.)
A. one physical interface for each subinterface
B. one IP network or subnetwork for each subinterface
C. a management domain for each subinterface
D. subinterface encapsulation identifiers that match VLAN tags
E. one subinterface per VLAN
F. subinterface numbering that matches VLAN tags
Answer: B,D,E
Explanation:
This scenario is commonly called a router on a stick. A short, well written article on this operation can be found here: http://www.thebryantadvantage.com/RouterOnAStickCCNACertificationExamTutorial.htm
Q5. Refer to the graphic.
R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Answer: D,F
Explanation:
This question is to examine the conditions for OSPF to create neighborhood.
So as to make the two routers become neighbors, each router must be matched with the following items:
1. The area ID and its types;
2. Hello and failure time interval timer;
3. OSPF Password (Optional).
Q6. Refer to the exhibit.
All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two.)
A. Network A - 172.16.3.48/26
B. Network A - 172.16.3.128/25
C. Network A - 172.16.3.192/26
D. Link A - 172.16.3.0/30
E. Link A - 172.16.3.40/30
F. Link A - 172.16.3.112/30
Answer: B,D
Explanation:
Only a /30 is needed for the point to point link and sine the use of the ip subnet-zero was used, 172.16.3.0/30 is valid. Also, a /25 is required for 120 hosts and again
172.16.3.128/25 is the best, valid option.
Q7. Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications?
A. RSA
B. L2TP
C. IPsec
D. PPTP
Answer: C
Explanation:
IPSec is a framework of open standards that provides data confidentiality, data integrity, and data authentication between participating peers at the IP layer. IPSec can be used to protect one or more data flows between IPSec peers.
Q8. Refer to the exhibit.
Switch-1 needs to send data to a host with a MAC address of 00b0.d056.efa4. What will Switch-1 do with this data?
A. Switch-1 will drop the data because it does not have an entry for that MAC address.
B. Switch-1 will flood the data out all of its ports except the port from which the data originated.
C. Switch-1 will send an ARP request out all its ports except the port from which the data originated.
D. Switch-1 will forward the data to its default gateway.
Answer: B
Explanation:
This question tests the operating principles of the Layer 2 switch. Check the MAC address table of Switch1 and find that the MAC address of the host does not exist in the table. Switch1 will flood the data out all of its ports except the port from which the data originated to determine which port the host is located in.
Switches work as follows:
u2711 Switches learn the MAC addresses of PCs or workstations that are connected to their switch ports by examining the source address of frames that are received on that port.
u2711 Machines may have been removed from a port, turned off, or moved to another port on the same switch or a different switch.
u2711 This could cause confusion in frame forwarding.
u2711 The MAC address entry is automatically discarded or aged out after 300 seconds
u2711 If there is not MAC address of destination host in MAC table, switch sends broadcast to all ports except the source to find out the destination host.
In output there is no MAC address of give host so switch floods to all ports except the source port.
Q9. It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following procedures are required to accomplish this task? (Choose three.)
A. Remove the IP address from the physical interface.
B. Encapsulate the physical interface with multipoint PPP.
C. Create the virtual interfaces with the interface command.
D. Configure each subinterface with its own IP address.
E. Disable split horizon to prevent routing loops between the subinterface networks.
F. Configure static Frame Relay map entries for each subinterface network.
Answer: A,C,D
Explanation:
For multiple PVCu2021s on a single interface, you must use subinterfaces, with each subinterface configured for each PVC. Each subinterface will then have its own IP address, and no IP address will be assigned to the main interface.
Q10. Refer to the exhibit.
How should the FastEthernet0/1 ports on the switches that are shown in the exhibit be configured to allow connectivity between all devices?
A. The ports only need to be connected by a crossover cable.
B. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-if)# switchport mode trunk
C. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-if)# switchport mode access SwitchX(config-if)# switchport access vlan 1
D. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-if)# switchport mode trunk SwitchX(config-if)# switchport trunk vlan 1 SwitchX(config-if)# switchport trunk vlan 10 SwitchX(config-if)# switchport trunk vlan 20
Answer: B
Explanation:
IN order for multiple VLANs to cross switches, the connection between the switches must be a trunk. The u201cswitchport mode trunku201d command is all that is needed, the individual VLANs should not be listed over that trunk interface.
Recommend!! Get the Actual 200-125 dumps in VCE and PDF From Certifytools, Welcome to download: https://www.certifytools.com/200-125-exam.html (New 889 Q&As Version)