Realistic VMware 2V0-41.20 Free Practice Test Online

NEW QUESTION 1
A DevOps user has deployed a Kubernetes Pod in vSphere. What does the term ClusterIP represent within NSX-T?

• A. Deployment of T1 with NLB service.
• B. Deployment of Distributed Router.
• C. Deployment of Distributed Load Balancing service.
• D. Deployment of T0 and T1

Answer: C

NEW QUESTION 2
Which NSX CLI command is used to check the GENEVE tunnel status on ESXi transport node?

• A. get host-switch <Host-Switch-Name> tunnels
• B. get transport-node tunnel status
• C. get host-switch <Host-Switch-Name> tunnel status
• D. get transport-node tunnel state

Answer: A

Explanation:
https://vdc-download.vmware.com/vmwb-repository/dcr-public/cc42e3c1-eb34-4567-a916-147e79798957/8264

NEW QUESTION 3
An NSX administrator wants to create a Tier-0 Gateway to support equal cost multi-path (ECMP) routing. Which failover detection protocol must be used to meet this requirement?

• A. Beacon Probing (BP)
• B. Host Standby Router Protocol (HSRP)
• C. Bidirectional Forwarding Detection (BFD)
• D. Virtual Router Redundancy Protocol (VRRP)

Answer: C

NEW QUESTION 4
What are two valid options when configuring the scope of a distributed firewall rule? (Choose two.)

• A. Segment Port
• B. Group
• C. Segment
• D. DFW
• E. Tier-1 Gateway

Answer: BD

NEW QUESTION 5
An NSX administrator is planning to deploy a multi-tier routing topology in their NSX-T Data Center environment to provide north-south connectivity for the VMs.
Which routing component must be deployed?

• A. Tier-1 Gateway
• B. Edge Services Gateway
• C. Tier-0 Gateway
• D. Layer 2 Gateway

Answer: C

NEW QUESTION 6
A customer has a network where BGP has been enabled and the BGP neighbor is configured on the Tier-0 Gateway. A NSX-T Data Center administrator used the get logical-routers command to retrieve this information:

Which two commands must be executed to check BGP neighbor status? (Choose two.)

• A. vrf 3
• B. vrf 1
• C. vrf 4
• D. sa-nsxedge-01(tier1_sr)> get bgp neighbor
• E. sa-nsxedge-01(tier0_sr)> get bgp neighbor
• F. sa-nsxedge-01(tier0_dr)> get bgp neighbor

Answer: AE

NEW QUESTION 7
How is the intra-tier transit link connection created between SR and DR for a Tier-0 Gateway?

• A. Manually create a gateway interface and mark it as transit.
• B. Automatically created when DR is created.
• C. Automatically created when SR is initialized.
• D. Manually create external uplink interface and mark it as transit.

Answer: C

NEW QUESTION 8
An NSX administrator has been tasked with deploying a NSX Edge Virtual machine through an ISO image. Which virtual network interface card (vNIC) type must be selected while creating the NSX Edge VM allow participation in overlay and VLAN transport zones?

• A. e1000
• B. VMXNET2
• C. VMXNET3
• D. Flexible

Answer: C

NEW QUESTION 9
Which CLI command shows syslog on NSX Manager?

• A. show log manager follow
• B. get log-file auth.log
• C. get log-file syslog
• D. /var/log/sysloq/syslog.log

Answer: C

Explanation:
https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.0/administration/GUID-406AF9C3-E8F7-447A-8E

NEW QUESTION 10
Which command is used to set the NSX Manager's logging-level to debug mode for troubleshooting?

• A. set service nsx-manager logging-level debug
• B. set service nsx-manager log-level debug
• C. set service manager log-level debug
• D. set service manager logging-level debug

Answer: D

Explanation:
https://vdc-download.vmware.com/vmwb-repository/dcr-public/cc42e3c1-eb34-4567-a916-147e79798957/8264

NEW QUESTION 11
Which three steps are required to create an IPsec VPN tunnel? (Choose three.)

• A. Create an IPsec service.
• B. Add a local endpoint.
• C. Configure an IPsec session.
• D. Configure a distributed firewall policy.
• E. Add a logical switch.

Answer: ABC

NEW QUESTION 12
Which network virtualization technologies can be used with an Ethernet VPN (EVPN) deployment in NSX-T Data Center? (Choose two.)

• A. Virtual Extensible Local Area Network (VXLAN)
• B. Multiprotocol Border Gateway Protocol (MP-BGP)
• C. Open Shortest Path First (OSPF)
• D. Multiprotocol Label Switching (MPLS)
• E. Virtual Routing and Forwarding (VRF)

Answer: AE

NEW QUESTION 13
What needs to be configured on a Tier-0 Gateway to make NSX Edge Services available to a VM on a VLAN- backed logical switch?

• A. Service interface
• B. Loopback Router Port
• C. Downlink interface
• D. VLAN Uplink

Answer: A

Explanation:
"The service interface is a special-purpose port to enable services for mainly VLAN-based networks.
North-south service insertion is another use case that requires a service interface to connect a partner appliance and redirect north-south traffic for partner services. Service interfaces are supported on both active-standby Tier-0 logical routers and Tier-1 routers. Firewall, NAT, and VPNs are supported on this interface. The service interface is also a downlink"

NEW QUESTION 14
An NSX administrator would like to export syslog events that capture messages related to NSX host preparation events.
Which message ID (msgid) should be used in the syslog export configuration command as a filter?

• A. SYSTEM
• B. FABRIC
• C. GROUPING
• D. MONITORING

Answer: B

Explanation:
https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.0/nsxt_30_admin.pdf

NEW QUESTION 15
What is the most restrictive NSX-T built-in role which will allow a user to apply configuration changes on a NSX Edge?

• A. Cloud Service Administrator
• B. Network Engineer
• C. Network Operator
• D. NSX Administrator

Answer: B

NEW QUESTION 16
What are three characteristics of a transport zone? (Choose three.)

• A. defines the potential reach of transport nodes
• B. configured with a Single N-VDS
• C. defines the scope and reachability of a Segment
• D. configured with multiple N-VDS
• E. optional for creating a segment

Answer: ABC

NEW QUESTION 17
Which command is used to display the network configuration of the Tunnel Endpoint (TEP) IP on a bare metal transport node?

• A. ifconfig
• B. tcpdump
• C. debug
• D. ipconfig

Answer: A

Explanation:
https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.0/installation/GUID-B7E7371E-A9F6-4880-B184

NEW QUESTION 18
Which three teaming policy modes are supported by NSX-T Data Center? (Choose three.)

• A. Destination MAC
• B. Load Balanced Source IP
• C. Failover Order
• D. Destination Port
• E. Load Balanced Source MAC
• F. Load Balanced Source

Answer: CEF

NEW QUESTION 19
An NSX administrator has configured a load balancer virtual server on a Tier-1 Gateway.
In order to advertise the load balancer virtual IP to the Tier-0 Gateway, which route advertisement configuration has to be done on the Tier-1 Gateway? (Choose two.)

• A. Advertise All LB SNAT IP Routes
• B. All Static Routes
• C. Information
• D. Advertise All LB VIP Routes
• E. Advertise All NAT Routes

Answer: AD

Explanation:
https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.0/administration/GUID-EEBA627A-0860-477A-9

NEW QUESTION 20
What are three NSX Manager roles? (Choose three.)

• A. cloud
• B. manager
• C. zookeeper
• D. policy
• E. master
• F. controller

Answer: BDF

NEW QUESTION 21
......