Cisco 300-160 Exam Dumps 2021

NEW QUESTION 1
What two options are common switching protocols that are used in the data center? (Choose two.)

• A. MPLS
• B. Frame Relay
• C. FDDI
• D. STP
• E. APPN/APPI

Answer: AD

NEW QUESTION 2
Which three actions must you perform to implement Cisco FabricPath on a data center network? (Choose three)

• A. Configure the VLAN in FabricPath mode
• B. Configure the interface to use the STP type of normal
• C. Configure the interfaces in FabricPath mode
• D. Configure the interfaces in trunk mode
• E. Enable the IS-IS feature
• F. Install the FabricPath feature set

Answer: ACF

NEW QUESTION 3
Which two options are valid methods for configuring VLANs on a Cisco UCS cluster? (Choose two.)

• A. globally per Cisco UCS cluster
• B. by using Cisco UCS Fabric Interconnect
• C. by using vPC domain configuration
• D. by using VTP
• E. by using CFS

Answer: AB

Explanation: http://www.cisco.com/c/en/us/support/docs/servers-unified-computing/ucs-2104xp-fabric-extender/110517-vlan

NEW QUESTION 4
Which technology provides additional scalability and simplification of an Ethernet network, providing more efficient forwarding and eliminating the need for the STP?

• A. OTV
• B. vPC
• C. PVST+
• D. FabricPath

Answer: D

NEW QUESTION 5
Which two options are reasons to use Layer 3 routing to segment a data center instead of Layer 2 switching? (Choose two.)

• A. limit the scope Spanning Tree Protocol
• B. limit the scope simplify design
• C. broadcast flooding
• D. ease of routing protocol configuration
• E. cost

Answer: AB

NEW QUESTION 6
Which solution enables you to scale up an IPS by load-balancing traffic to servers or appliances?

• A. Cisco ITD
• B. Cisco AMP
• C. Cisco ASA with FirePOWER Services
• D. PBR

Answer: A

NEW QUESTION 7
Which two actions must be performed when you configure Cisco VN-Link in hardware? (Choose two.)

• A. Create a distributed virtual switch in Cisco UCS Manager.
• B. Add an ESX host to the distributed virtual switch in Cisco UCS Manager.
• C. Create a port profile and profile clients in Cisco UCS Manager.
• D. Create a standard switch on an ESXi host and map the network adapters to the switch.
• E. Create a distributed virtual switch under the datacenter folder in VMware vCenter.

Answer: AC

NEW QUESTION 8
When migrating an existing data center network to a unified fabric network, which transitions should you expect to see?

• A. IOS to Nexus networking equipment
• B. physical to virtual machines
• C. Fibre Chanel to FCoE
• D. iSCSI to NAS

Answer: C

NEW QUESTION 9
What is required when configuring the second fabric interconnect in a cluster configuration?

• A. The IP address of the default gateway must be on the same subnet as the peer fabric interconnect.
• B. The system name of the second fabric interconnect must be different from the system name of the first fabric interconnect.
• C. The IP address of the management port must be in the same subnet as the peer fabric interconnect.
• D. The first and the second fabric interconnects must be able to reach the DNS.

Answer: B

NEW QUESTION 10
Which two Nexus 7000 licenses are required to manage FabricPath from Cisco Data Center Network Manager (DCNM)? (Choose two.)

• A. Nexus 7000 Enhanced Layer 2 License
• B. Nexus 7000 Transport Services License
• C. Cisco DCNM for SAN Advanced Edition for Nexus 7000
• D. Nexus 7000 LAN Enterprise License
• E. Cisco DCNM for Nexus 7000
• F. Nexus 7000 Scalable Feature License

Answer: AE

NEW QUESTION 11
You must provide dedicated bandwidth to a blade server on a Cisco UCS chassis. To which type of ports should you pin the blade server vNlCs and vHBAs?

• A. dedicated server
• B. dedicated switch
• C. dedicated uplink
• D. dedicated IOM

Answer: C

NEW QUESTION 12
You have a Cisco UCS B-Series chassis. To connect to a blade server by using a remote KVM console, you should connect to the IP address of which component?

• A. mgmt0
• B. CIMC
• C. IPMI
• D. CMP

Answer: B

NEW QUESTION 13
Which components share a physical interface in a VDC deployment?

• A. two VDCs for Ethernet traffic
• B. storage VDC for FCoE traffic and a VDC for Ethernet traffic
• C. two storage VDCs for FCoE traffic
• D. interface VLAN and a VDC

Answer: B

NEW QUESTION 14
Which two options are reasons to use Layer 3 routing to segment a data center instead of Layer 2 switching? (Choose two)

• A. Simply design
• B. Ease of routing protocol configuration
• C. Limit the scope of broadcast flooding
• D. Cost
• E. Limit the scope of spanning Tree Protocol

Answer: CE

NEW QUESTION 15
In a three-tier SAN topology, which network layer should you connect the SAN initiators to?

• A. storage edge
• B. core
• C. host edge
• D. distribution

Answer: C

NEW QUESTION 16
You are designing a data center network using Cisco Nexus 7000 Series switches. Which feature should be configured to control the rate at which packets are allowed to reach the Supervisor?

• A. relaxed process startup
• B. port channel load balancing method
• C. embedded event manager
• D. data plane policing
• E. control plane policing

Answer: E

NEW QUESTION 17
Which two characteristics are associated with the access layer of a Data Center Unified Fabric network? (Choose two)

• A. voice, data, and wireless convergence
• B. no packet manipulation
• C. QoS—policing
• D. routing manipulation and filtering
• E. QoS - classification and queuing

Answer: AE

NEW QUESTION 18
Which software runs on a device that is connected to a TrustSec-enabled port?

• A. Requester
• B. Authenticator
• C. Supplicant
• D. Authentication Proxy

Answer: C

NEW QUESTION 19
Which option must be enabled to allow line-rate forwarding on a Fibre Channel port?

• A. F port
• B. TEport
• C. dedicated mode
• D. shared mode
• E. E port

Answer: C