Testking mature Alcatel-Lucent lecturers and also experts can approve that Testking Alcatel-Lucent 4A0-M01 examination answers and questions are almost proper. The particular pass price regarding Alcatel-Lucent IP/MPLS Mobile Backhaul Transport has been almost 95 %. Previously mentioned ing, we might demonstrate the 4A0-M01 examine supplies made useful guide for Alcatel-Lucent prospects. Our own 4A0-M01 pdf worth the examinees sparing with out to study. It is possible to guess your own shoe you will have a optimistic result from the Testking Alcatel-Lucent IP/MPLS Mobile Backhaul Transport practice checks.
2021 Dec 4A0-M01 rapidshare
Q21. Which statement is correct concerning spoke SDP use in point-to-point services?
A. Each service requires its own set of SDPs
B. The spoke SDP must specify the vc-type of the service transported
C. SDP bindings must include the service encapsulation type value
D. An explicit endpoint may have up to four spoke SDP bindings E. Each service includes two default explicit endpoints
Answer: D
Q22. Click on the exhibit.
Given the configuration shown, and the following condition:
. The next hop interface on the preferred path to prefix 192.0.2.0/32 failed
. Label Distribution Protocol (LDP) is enabled on the interfaces How long does the router wait before it moves traffic to the secondary route for this prefix?
A. 900 ms
B. 1.5 seconds
C. 45 seconds
D. 60 seconds
Answer: A
Q23. Click on the exhibit Given the diagram and the following information:
. Virtual Private Routed Network (VPRN) 5 spans the routers Point of Concentration (POC) 3-1 and 3-2 and the Multilevel Switch (MLS) routers MLS1 and MLS2
. Multiprotocol Border Gateway Protocol (MP-BGP) is configured and operational
. Pseudowire status is signaled, as shown, on the ePipe/VPRN spoke Service Distribution Points (SDPs)
What might you configure on the services illustrated to hold down the primary VPRN NodeB loopback interface static route in case of an intermittent or rapid spoke SDP failure and recovery?
A. Set port hold down timers on the CSA to POC3-1 link
B. Configure Label Distribution Protocol (LDP) Sync on the VPRN static routes
C. Enable BGP next-hop tracking in the VPRN BGP peer groups
D. SetareverttimervalueontheCSAePipe50endpoint
Answer: A
Q24. Which is a characteristic of the IEEE 802.3 Slow Protocol?
A. There are a maximum of 10 frames transmitted per second
B. There are a maximum of 20 slow protocol subtypes per interface
C. The maximum slow protocol frame size is 64 bytes
D. The slow protocol header carries the clock quality level
Answer: A
Q25. Which quality level will MLS1 deliver to POC2-1 on its Synchronous Ethernet (SyncE) port 1/2/7?
A. QL-DUS
B. QL-EEC2
C. QL-PRS
D. QL-STU
Answer: C
Far out 4A0-M01 exam answers:
Q26. Choose the two SAP identifiers that a Cross Connect ID (CCID) can bind to create a bi-directional Layer 2 and Layer 3 service cross connect. (Choose two.)
A. sap 1/1/9:100:200
B. sap 1/1/8:100:200
C. sapccag-l.a:l00
D. sapccag-2.a:100
E. sapccag-1.b:100
F. sap ccag-2.b:200
Answer: C, E
Q27. Which IEEE 1588v2/Precision Time Protocol (PTP) v2 message carries the second master time stamp value used in a two-way operation for Packet Delay Variation (PDV) calculations?
A. Announce
B. Sync
C. Announce_granted
D. Delay_Response
Answer: D
Q28. Click on the exhibit
Given the configuration shown:
What must you configure in the cPipe service to allow it to set the service's payload and jitter buffer sizes?
A. Configure CEM on the TDM port channel group
B. Configure CEM on the SAP
C. Configurethejitterbufferinthebaseservice context
D. Set the service Maximum Transmission Unit (MTU)
Answer: B
Q29. Which statement correctly describes the IEEE 1588v2 two-way synchronization operating mode?
A. The slave nodes send Follow_up messages after each Sync message
B. The slave sets its clock offset based on a pair of received Sync messages
C. The slave uses two sets oftimestamps to calculate its clock offset
D. The slave verifies the Sync messages with associated Follow_up messages
Answer: C
Q30. Which two wireless technologies has the 3rd Generation Partnership Project 2 (3GPP2) developed? (Choose two.)
A. 2G Global Systems for Mobile (GSM)
B. 2G Code Division Multiple Access (CDMA)
C. 2.75G Enhanced Data Rates for GSM Evolution (EDGE)
D. 3G Universal Mobile Telecommunications System (UMTS)
E. 3G Evolution-Data Optimized (EV-DO)
F. 4G Long Term Evolution (LTE)
Answer: B, E