Getting your Alcatel-Lucent Alcatel-Lucent certification is the fantasy of many IT aspirants. But passing the Alcatel-Lucent 4A0-M01 exam isnt an effortless task with out any helpful preparatory materials. The first step is always to find a great abundant resource for the Alcatel-Lucent 4A0-M01 exam preparation. Now Exambible comes to help you. The 4A0-M01 exam in addition names Alcatel-Lucent Alcatel-Lucent exam thats a Alcatel-Lucent certification. And also Exambible provides you with all of the Alcatel-Lucent certification exam products which includes the Alcatel-Lucent 4A0-M01 exam demos.

2021 Dec 4A0-M01 brain dumps

Q41. Click on the exhibit. 

Given the local Provider Edge (PE) router configuration shown: 

Assuming equal status on both spoke Service Distribution Points (SDPs), how does the local PE router choose the active SDP? 

A. It chooses the first operational spoke SDP 

B. Itforwards traffic over both spoke SDPs simultaneously 

C. It chooses the spoke SDP with the lowest numeric SDP ID 

D. It chooses the spoke SDP with the lowest numeric VC ID 

Answer:


Q42. Which statement correctly describes the Point-to-Point (PPP) Multilink Protocol (MP) negotiation process? 

A. At least one link must complete Link Control Protocol (LCP) negotiations before the bundle can initialize 

B. The endpoints indicate their desire to implement MP in the link Network Control Protocol (NCP) phase 

C. The bundle must  complete  LCP negotiations  before it can enter the NCP negotiation phase 

D. Internet Protocol-Control Protocol (IPCP) negotiations must succeed for the bundle links to initialize 

Answer:


Q43. Which statement correctly descnbes pseudowire switched Virtual Private Wire Service (VPWS) creation? 

A. You must use the vc-switching keyword on both the Terminating and Switching Provider Edge (T-PE/S-PE) routers 

B. You must create an explicit endpoint on the S-PE services 

C. The S-PE may include Services Access Points (SAPs) for local service access 

D. The T-PE router services may include as many as four redundant pseudowires 

Answer:


Q44. When researching carrier-class Ethernet standards to support the mobile backhaul Ethernet transport, which standards body would you consult? 

A. IEEE 

B. MEF 

C. ITU-T 

D. NGMN 

Answer:


Q45. Given the topology and the Multiprotocol Label Switching (MPLS) Label Switch Path (LSP) and path configurations shown: You wish to protect the LSP POC3-1_POC3-2 with a manual bypass tunnel. Which statement correctly describes the manual bypass tunnel configuration requirement for the ring topology shown? 

A. All nodes must have manual bypass enabled in the MPLS context 

B. All nodes must have fast reroute facility enabled in the MPLS context. 

C. The bypass tunnel first hop must avoid the protected LSP's tail end router 

D. Each node must have a bypass-only tunnel configured to terminate on POC3-2 

Answer:


Renewal 4A0-M01 practice:

Q46. Click on the exhibit Given the show command and the result shown: Which payload type does this service transport? 

A. A channelized E1 circuit carrying all 32 timeslots 

B. An unframedDSI circuit carrying all 24 timeslots 

C. Multilink Protocol (MP) framed bundled E1s 

D. Ethernet over TDM framed DS1 circuits 

Answer:


Q47. Given the topology and the Multiprotocol Label Switching (MPLS) Label Switch Path (LSP) and path configurations shown: You wish to protect the LSP POC3-1_POC3-2 with a manual bypass tunnel. Which statement correctly describes the requirement for implementing a manual bypass tunnel on router POC3-1? 

A. The manual bypass tunnel must merge to the original path 

B. You must enable manual bypass in the LSP POC3-1_POC3-2 context 

C. Fast-reroute one-to-one must be configured on the protected LSP 

D. The manual bypass tunnel path must avoid router POC3-2 

Answer:


Q48. Which field in the show command result indicates that the router MLS1 is configured as a Border Gateway Protocol (BGP) route reflector? 

A. Peer Type; 

B. Group: 

C. Peer AS: 

D. Cluster Id: 

Answer:


Q49. Click on the exhibit. 

Given the diagram shown and the following information: 

. CSA1 originates a redundant ePipe service 

. The ePipe spoke Service Distribution Points (SDPs) terminate on Internet Enhanced Services (ES) configured on each of the two remote PEs. 

. The ePipe service Maximum Transmission Unit (MTU) is set to 1518 How must  you configure the IES MTUs to ensure that the spoke SDPs  become operational on all bound services? 

A. configure the IES service MTU to 1500 bytes 

B. configure the IES interface IP-MTUs to 1504 bytes 

C. configure the IES spoke SDP path MTUs to 1518 bytes 

D. configure the remote PE SDP path MTUs to 1518 bytes 

Answer:


Q50. What function does a Backhaul Transport Provider (BTP) Aggregation Gateway (BG) perform in the backhaul transport? 

A. It originates and terminates mobile operator service tunnels 

B. It provides Automatic Protection Switching (APS)  protected interfaces to the MTSO NC elements 

C. It presents Layer 3 interfaces to the MG and CSA devices 

D. It delivers point-to-point Ethernet or TDM transport to the MSPs 

Answer: