Renewal Service Provider Routing And Switching - Professional (JNCIP-SP) JN0-662 Dumps Questions

NEW QUESTION 1
You have configured Layer 2 VPN stitching between two Layer 2 circuits on PE2, but traffic is not passing through the VPN.

Referring to the exhibit, what is the problem?

• A. The unit 1 peer unit must be set to 0.
• B. The VLAN IDs must be lower than 512.
• C. The VLAN IDs must be different on each unit.
• D. The peer units must reference the VLAN IDs.

Answer: A

NEW QUESTION 2
Click the Exhibit button.

Referring to the exhibit, why are R1 and R2 not exchanging routes between their VPNs?

• A. The route targets are not property configured.
• B. The IP addresses in the BGP configuration must be in the same subnet.
• C. The interfaces unit numbers must be the same on both sides.
• D. The route distinguishers are not properly configured.

Answer: D

NEW QUESTION 3
Click the Exhibit button.

Referring to the exhibit, when building an interprovider VPN Option C between AS65100 and AS65200, which two parameters must be configured on the EBGP connection between PE1 and PE2? (Choose two.)

• A. family inet-vpn unicast
• B. multihop
• C. family inet labeled-unicast
• D. multipath

Answer: AB

NEW QUESTION 4
Click the Exhibit button.

Referring to the exhibit, which statement is correct?

• A. IP address 192.168.16.5 is on a directly connected interface.
• B. Four routes have been leaked from the Level 2 area to the Level 1 area.
• C. The path to IP address 192.168.16.6 is currently unavailable.
• D. R1 has two Level 2 adjacencies and one Level 1 adjacency to other routers.

Answer: A

NEW QUESTION 5
Click the Exhibit button.

Which two statements are true about the route shown in the exhibit? (Choose two.)

• A. The route is currently active.
• B. The route is currently hidden.
• C. The route has an unreachable next-hop.
• D. The route is currently being damped.

Answer: B

NEW QUESTION 6
Your company has multiple upstream BGP connections to the Internet through ISP-A, ISP-B, and ISP-C. You want to ensure that all traffic coming into your network uses ISP-A.
How would you accomplish this task?

• A. Change the route preference to be higher on routes being advertised to ISP-B and ISP-C.
• B. Prepend your AS number on routes being advertised to ISP-A.
• C. Change the local preference to be higher on routes being advertised to ISP-A.
• D. Prepend your AS number on routes being advertised to ISP-B and ISP-C.

Answer: D

NEW QUESTION 7
According to Juniper Networks, what are three methods of scaling Layer 2 VPNs? (Choose three.)

• A. inbound route filters
• B. route reflection
• C. outbound route filters
• D. filter-based forwarding
• E. BGP route refresh

Answer: ABC

NEW QUESTION 8
Which neighbor state indicates that two BGP neighbors have full connectivity?

• A. Idle
• B. Connect
• C. OpenConfirm
• D. Established

Answer: D

NEW QUESTION 9
You are asked to configure PIM-SM in your network. Your implementation must allow for load sharing between redundant RPs and, should an RP failure occur, the RP failover time should be minimized.
Which two configuration tasks are required in this scenario? (Choose two.)

• A. Configure MSDP peering sessions between the routers designated as RPs.
• B. Configure the shared anycast address on the RPs as the primary address on the loopback interface.
• C. On the routers designated as RPs, configure the shared anycast address on the loopback interface.
• D. Configure at least two static RPs and bundle them in an RP redundancy group under [edit protocols pim].

Answer: BD

NEW QUESTION 10
You are asked to configure a new Layer 3 VPN.
In this scenario, which routing-instance type must be used?

• A. vpls
• B. evpn
• C. vrf
• D. 12vpn

Answer: C

NEW QUESTION 11
Click the Exhibit button.

Referring to the exhibit, what must be added to the existing configuration to ensure that per-prefix load balancing occurs?

• A. multihop
• B. keep all
• C. multipath
• D. family inet unicast

Answer: C

NEW QUESTION 12
You have deployed class of service on your network. You notice that the single strict-high queue is starving traffic to all other queues. What will help to ensure that all queues receive the desired transmission rates?

• A. Configure the rate-limit parameter on the strict-high queue.
• B. Set the packet-loss priority to high on the other queues.
• C. Change the other forwarding-classes to a lossless queue.
• D. Increase the priority of all queues to high priority

Answer: A

NEW QUESTION 13
Click the Exhibit button.

Which two statements are true regarding the output shown in the exhibit? (Choose two.)

• A. Both ESIs are generated from the router ID.
• B. Both ESIs use the same VNI.
• C. The ESI 05:00:00:fe:4d:00:00:56:0e:00 is an auto-generated ES
• D. The ESI 00:24:24:24:24:24:24:24:24:24 is an auto-generated ESI.

Answer: BC

NEW QUESTION 14
Which two protocols are available in the Junos OS for the data plane encapsulation of EVPN traffic? (Choose two.)

• A. MPLS
• B. IPsec
• C. VXLAN
• D. GRE

Answer: AC

NEW QUESTION 15
Click the Exhibit button.

Referring to the exhibit, you want to ensure that routers in Area 20 can connect to routers in Area 0. Which two steps must be done to allow this behavior? (Choose two.)

• A. A virtual link must be configured under R2 Area 0 and R4 Area 0.
• B. Area 10 must be configured as a stub area.
• C. A virtual link must be configured under R2 Area 0 and R4 Area 20.
• D. Area 10 must be configured as a standard area.

Answer: AD

NEW QUESTION 16
Click the Exhibit button.

The exhibit shows a BGP peering session for two PE routers. The BGP session is up, but IPv4 hosts in the Layer 3 VPN that use the BGP session are unable to communicate.
What is the problem?

• A. The BGP peer does not support the add-path feature.
• B. The BGP peer does not support the restarter functionality.
• C. The local BGP router does not support Layer 2 VPN and Layer 3 VPN NLRI address families at the same time.
• D. There is a mismatch in the supported NLRI address families between the BGP peers.

Answer: D

NEW QUESTION 17
Click the Exhibit button.

R5 must advertise Subnet A into IS-IS so that Subnet A and Subnet B can communicate. Subnet B must be able to forward traffic to Subnet A and towards Area 49.0001. However, R5 should not be able to route traffic from Subnet A to Area 49.0001.
Referring to the exhibit, how would you solve this problem?

• A. Configure Level 2 on all links in Area 49.0002.
• B. Configure the set protocols isis ignore-attached-bit parameter on R5.
• C. Configure the set protocols isis overload parameter on R6.
• D. Configure an export policy on R6 to reject all routes except Subnet B towards R5.

Answer: B

NEW QUESTION 18
You are configuring a BGP-signaled Layer 2 VPN service. Which two statements are true in this scenario? (Choose two.)

• A. RSVP-signaled LSPs are required.
• B. The family 12vpn auto-discovery-only parameter is required for BGP sessions.
• C. The family 12vpn signaling parameter is required for BGP sessions.
• D. RSVP-signaled or LDP-signaled LSPs may be used.

Answer: CD

NEW QUESTION 19
Click the Exhibit button.



Routers R1, R2, and R3 have set protocols isis interface all configured and no other set protocols isis
configuration.
Referring to the exhibit, which two statements are true? (Choose two.)

• A. The R2-R3 link will form a Level 1 and Level 2 adjacency.
• B. The R1-to-R2 link will only form a Level 2 adjacency.
• C. The R1-to-R2 link will form a Level 1 and Level 2 adjacency.
• D. The R2-R3 link will only form a Level 1 adjacency.

Answer: AC

NEW QUESTION 20
Which transport mechanism is required for Layer 3 VPNs?

• A. GRE
• B. VXLAN
• C. IPsec
• D. MPLS

Answer: D

NEW QUESTION 21
Click the Exhibit button.

Referring to the exhibit, what is the correct prefix length of the route for the multihomed device?

• A. 192
• B. 304
• C. 296
• D. 248

Answer: B

NEW QUESTION 22
Which two types of LSAs have a domain scope? (Choose two.)

• A. Type 7
• B. Type 2
• C. Type 10
• D. Type 5

Answer: CD

NEW QUESTION 23
Click the Exhibit button.

R1 and R2 are not forwarding the routes received from a remote PE to their customers.
Referring to the exhibit, which parameter must be added to the configuration to allow the routes to be forwarded?

• A. multipath multiple-as
• B. family inet-vpn
• C. multihop
• D. as-override

Answer: B

NEW QUESTION 24
Click the Exhibit button.

You administer AS 65000, and have deployed a route reflector (RR1) in your network as shown in the exhibit. The traffic between AS 65001 and AS 65002 is going through the route reflector, even though it is not the best path.
What will solve this problem?

• A. Change the LOCAL_PREF so that it uses the preferred path.
• B. Remove the nhs policy.
• C. Change the originator to be the preferred path.
• D. Change the IGP metric so it is lower on the preferred path.

Answer: B

NEW QUESTION 25
Click the Exhibit button.

Referring to the exhibit, which two statements are true? (Choose two.)

• A. A BGP full mesh is only required between PE-1 and PE-2.
• B. A BGP full mesh is required between P1, P2, PE-1, and PE-2.
• C. MPLS must only be enabled on PE-1 and PE-2.
• D. MPLS must be enabled on P1, P2, PE-1, and PE-2.

Answer: AD

NEW QUESTION 26
......