The Secret Of Cisco 300-410 Exam Price

NEW QUESTION 1

Refer to the exhibit.

A router receiving BGP routing updates from multiple neighbors for routers in AS 690. What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.1.1?

• A. The local preference value in another neighbor statement is higher than 250.
• B. The local preference value should be set to the same value as the weight in the route map.
• C. The route map is applied in the wrong direction.
• D. The weight value in another neighbor statement is higher than 200.

Answer: C

NEW QUESTION 2

Refer to the exhibit.

An administrator configured a Cisco router for TACACS authentication, but the router is using the local enable password instead Which action resolves the issue?

• A. Configure the aaa authentication login admin group admin local enable command instead.
• B. Configure the aaa authentication login admin group tacacs* local enable none command instead.
• C. Configure the aaa authentication login admin group tacacs* local if-authenticated command instead.
• D. Configure the aaa authentication login default group admin local if-authenticated command instead.

Answer: C

NEW QUESTION 3

Which two components are required for MPLS Layer 3 VPN configuration? (Choose two)

• A. Use pseudowire for Layer 2 routes
• B. Use MP-BGP for customer routes
• C. Use OSPF between PE and CE
• D. Use a unique RD per customer VRF
• E. Use LDP for customer routes

Answer: CD

NEW QUESTION 4



Refer to the exhibit. An administrator must harden a router, but the administrator failed to test the SSH access successfully to the router. Which action resolves the issue?

• A. Configure SSH on the remote device to log m using SSH
• B. SSH syntax must be ssh -I user ip to log in to the remote device
• C. Configure enable secret to log in to the device
• D. SSH must be allowed with the transport output ssh command

Answer: B

NEW QUESTION 5


Refer to the exhibit. An engineer examines the BGP update for the IPv6 prefix 2001:db8::1/128. which should have been summarized into a /64 prefix. Which sequence of actions achieves the summarization?

• A. R1 is a route reflector client of a RR with a router ID of 1.1.1.1. and the originator of the prefix has a router ID of 3.3.3.3. Both routers belong to different AS
• B. The prefix is not advertised to any peer and must be advertised using the network statement on R3.
• C. R1 is a route reflector with a router ID of 3.3.3.3. and the originator of the prefix is a route reflector client, which has a router ID of 3.3.3.3. Both routers belong to the same AS Configure an aggregate address on the router with ID 1.1.1.1 for the prefix
• D. R1 is a route reflector with a router ID of 1.111. and the originator of the prefix is a route reflector client, which has a router ID of 3.3.3.3. Both routers belong to the same AS Configure an aggregate address on the router with ID 1.1.1.1 for the prefix
• E. R1 is a route reflector client of a RR with a router ID of 1.1.1.1. and the originator of the prefix has a router ID of 3.3.3.3. Both routers belong to the same A
• F. Configure an aggregate address on the router with ID 3 3.3.3 for the prefix.

Answer: D

NEW QUESTION 6

An engineer configured a Cisco router to send reliable and encrypted notifications for any events to the management server. It was noticed that the notification messages are reliable but not encrypted. Which action resolves the issue?

• A. Configure all devices for SNMPv3 informs with priv.
• B. Configure all devices for SNMPv3 informs with auth.
• C. Configure all devices for SNMPv3 traps with auth.
• D. Configure all devices for SNMPv3 traps with priv.

Answer: A

Explanation:
SNMP notifications can be sent as traps or inform requests. Traps are unreliable because the receiver does not send acknowledgments when this device receives traps.”Send reliable and encrypted notifications for any events” so it is SNMP notifications. For encryption we need to configure “priv”.

NEW QUESTION 7

Refer to the exhibit.

What is the result of applying this configuration?

• A. The router can form BGP neighborships with any other device.
• B. The router cannot form BGP neighborships with any other device.
• C. The router cannot form BGP neighborships with any device that is matched by the access list named “BGP”.
• D. The router can form BGP neighborships with any device that is matched by the access list named “BGP”.

Answer: C

Explanation:
after bgp session are UP.I configured the CoPP to drop 10.3.3.3 bgp traffic (R3). R3 bgp traffic that matched the ACL 100 is dropped and the state is in IDLE
-------------------------------------------
access-list 100 permit tcp host 10.3.3.3 any eq bgp access-list 100 permit tcp host 10.3.3.3 eq bgp any
!
class-map match-all class-bgp match access-group 100
!
policy-map policy-bgp class class-bgp
drop
!
control-plane
service-policy input policy-bgp
!
The 10.3.3.3 neighbor goes to IDLE

NEW QUESTION 8

Refer to the exhibit.
A network administrator is troubleshooting OSPF adjacency issue by going through the console logs in the router, but due to an overwhelming log message stream it is impossible to capture the problem Which two commands reduce console log messages to relevant OSPF neighbor problem details so that the issue can be resolved? (Choose two)

• A. debug condition interface
• B. debug condition ip
• C. debug condition ospf neighbor
• D. debug condition session-id ADJCHG
• E. debug condition all

Answer: AD

NEW QUESTION 9

Refer to the exhibit.

When the FastEthemet0/1 goes down, the route to 172.29.0 0/16 via 192.168.253 2 is not installed in the RIB. Which action resolves the issue?

• A. Configure reported distance greater than the feasible distance
• B. Configure feasible distance greater than the successor's feasible distance.
• C. Configure reported distance greater than the successor's feasible distance.
• D. Configure feasible distance greater than the reported distance

Answer: D

Explanation:
From the exhibit, we notice network 172.29.0.0/16 was learned via two routes:
+ From 192.168.254.2 with FD = 307200 and AD = 281600
+ From 192.168.253.2 with FD = 410200 and AD = 352300
The first route is installed into the RIB as the successor route because of lower FD.
When the first route fails, router will not use the second route as it does not satisfy the feasibility condition. The feasibility condition states that, the Advertised Distance (AD, also called the reported distance) of a route must be lower than the feasible distance of the current successor route.

NEW QUESTION 10


Refer to the exhibit. A network administrator configured NetFlow data, but the data is not visible at the NetFlow collector. Which configuration allows the router to send the records?

• A. Configure the management interface in the global routing table to send the records.
• B. Configure a different interface to send the records.
• C. Configure the NetFlow collector to listen at export-protocol netflow-v5.
• D. Rectify NetFlow collector reachability from the management interface.

Answer: B

NEW QUESTION 11

Drag and drop the MPLS terms from the left onto the correct definitions on the right.

• A. Yes
• B. Not Mastered

Answer: A

NEW QUESTION 12

An engineer is configuring a network and needs packets to be forwarded to an interface for any destination address that is not in the routing table. What should be configured to accomplish this task?

• A. set ip next-hop
• B. set ip default next-hop
• C. set ip next-hop recursive
• D. set ip next-hop verify-availability

Answer: B

Explanation:

NEW QUESTION 13

Refer to Exhibit.

Traffic from the branch network should route through HQ R1 unless the path is unavailable. An engineer tests this functionality by shutting down interface on the BRANCH router toward HQ_R1 router but 192.168.20.0/24 is no longer reachable from the branch router. Which set of configurations resolves the issue?

• A. HQ_R1(config)# ip sla responderHQ_R1(config)# ip sla responder icmp-echo 172.16.35.2
• B. BRANCH(config)# ip sla 1BRANCH(config-ip-sla)# icmp-echo 172.16.35.1
• C. HQ_R2(config)# ip sla responderHQ_R2(config)# ip sla responder icmp-echo 172.16.35.5
• D. BRANCH(config)# ip sla 1BRANCH(config-ip-sla)# icmp-echo 172.16.35.2

Answer: D

Explanation:
In the configuration above, the engineer has made a mistake as he was tracking 172.16.35.6 (the backup path) instead of tracking the main path (172.16.35.2). Therefore,when he shut down the main path, the track 1 was still up so traffic still went through the main path -> it failed.
To fix this issue, we just need to correct the tracking interface of the main path.

NEW QUESTION 14

An engineer configured VRF-Lite on a router for VRF blue and VRF red. OSPF must be enabled on each VRF to peer to a directly connected router in each VRF. Which configuration forms OSPF neighbors over the network 10.10.10.0/28 for VRF blue and 192.168.0.0/30 for VRF red?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: A

NEW QUESTION 15

Which statement about route distinguishers in an MPLS network is true?

• A. Route distinguishers allow multiple instances of a routing table to coexist within the edge router.
• B. Route distinguishers are used for label bindings.
• C. Route distinguishers make a unique VPNv4 address across the MPLS network.
• D. Route distinguishers define which prefixes are imported and exported on the edge router.

Answer: C

NEW QUESTION 16

What is the purpose of an OSPF sham-link?

• A. to allow intra-area routing when OSPF is used as the PE-CE connection protocol in an MPLS VPN network
• B. to correct OSPF backdoor routing when OSPF is used as the PE-CE connection protocol *i an MPLS VPN network
• C. to correct OSPF backdoor routing when OSPF is used as the PE-PE connection protocol m an MPLS VPN network
• D. to allow inter-area routing when OSPF is used as the PE-CE connection protocol in a MPLS VPN network

Answer: C

NEW QUESTION 17

Refer to the exhibit.

Why is the remote NetFlow server failing to receive the NetFlow data?

• A. The flow exporter is configured but is not used.
• B. The flow monitor is applied in the wrong direction.
• C. The flow monitor is applied to the wrong interface.
• D. The destination of the flow exporter is not reachable.

Answer: A

NEW QUESTION 18

Refer to the exhibits.

A user on the 192.168.1.0/24 network can successfully ping 192.168.3.1, but the administrator cannot ping 192.168.3.1 from the LA router. Which set of configurations fixes the issue?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: B

NEW QUESTION 19


Refer to the exhibit A CoPP policy is implemented to allow specific control traffic, but the traffic is not matching as expected and is getting unexpected behavior of control traffic. Which action resolves the issue?

• A. Use match-any instruction in class-map
• B. Create a separate class map against each ACL.
• C. Create a separate class map lor ICMP traffic.
• D. Use default-class to match ICMP traffic

Answer: A

NEW QUESTION 20

Refer to the exhibit.

A network administrator configured mutual redistribution on R1 and R2 routers, which caused instability in the network. Which action resolves the issue?

• A. Set a tag in the route map when redistributing EIGRP into OSPF on R1. and match the same tag on R2 to allow when redistributing OSPF into EIGRP.
• B. Apply a prefix list of EIGRP network routes in OSPF domain on R1 to propagate back into the EIGRP routing domain.
• C. Set a tag in the route map when redistributing EIGRP into OSPF on R1, and match the same tag on R2 to deny when redistributing OSPF into EIGRP.
• D. Advertise summary routes of EIGRP to OSPF and deny specific EIGRP routes when redistributing into OSPF.

Answer: C

Explanation:
https://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/8606-redist.ht

NEW QUESTION 21
......