A Review Of Download 350-501 Brain Dumps

NEW QUESTION 1
Refer to the exhibit:

If router RA is configured as shown, which IPv4 multicast address space does it use?

• A. 224.0. 0.0/8
• B. 225.0. 0.0/8
• C. 232.0. 0.0/8
• D. 239.0. 0.0/8

Answer: C

NEW QUESTION 2
Refer to the exhibit.

A network engineer is implementing a standard customer route-policy on ASBR1 with these requirements:
• It must accept only customer-assigned prefixes
• It must preserve customer advertised BGP communities
• It must set the local-preference to 110 for all prefixes
• It must attach the ORIGINATION-PE and LOCAL-CITY communities to all accepted prefixes. Which route policy must the engineer implement on ASBR1 to satisfy the requirements?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: D

NEW QUESTION 3
Refer to the exhibit.

What is the result of this configuration?

• A. Router 1 opens and closes a TCP connection to the TACACS+ server every time a user requires authorization.
• B. Router 1 and the TACACS+ server maintain one open connection between them only when network administrator is accessing the router with password ciscotest.
• C. Router 1 and the TACACS+ server maintain one open connection between them.
• D. Router 1 opens and closes a TCP connection to the TACACS+ server every time a user requires authentication.

Answer: C

Explanation:
https://www.ccexpert.us/cisco-secure/configuring-tacacs-on-cisco-ios.html
single-connection (Optional) Used to specify a single connection. Rather than have the router open and close a TCP connection to the daemon each time it must communicate, the single-connection option maintains a single open connection between the router and the daemon. This is more efficient because it allows the daemon to handle a higher number of TACACS operations.

NEW QUESTION 4
Refer to the exhibit

Routers R1 and R2 are connected via a señal link and use the IS-IS routing protocol for route exchange After a configuration change on R2. IS-IS connectivity is interrupted A network engineer confirmed that the interfaces are in the UP state and connectivity exists between the two routers. Which two actions must the engineer perform to resolve the problem? (Choose two.)

• A. Disable padding for hello packets under the serial interface on R2 DUMPS
• B. Change the hello interface timer to 10 seconds on R1.
• C. Change the MTU to 1500 bytes on R2.
• D. Enable hello packet padding globally on R1.
• E. Change R2 to an IS-IS Level 1 router.

Answer: CE

NEW QUESTION 5
Refer to the exhibit.

A network operator must configure CSR1 interlaces GigabitEihernet2 and GigabitEthemet to rewrite VLAN tags 12 and 21 for traffic between R1 and R2 respectively. Which configurator accomplishes this task?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: B

NEW QUESTION 6
Refer to the exhibit.

Over the last few months. ISP A has doubled Its user base. The IT Director asked the engineering team to monitor memory consumption and buffer statistics on all P and PE devices In the MPLS core. Most devices have CPU usage of 70% or more, so the solution must be targeted and secure. Which two commands must the engineering team implement on P and PE devices to meet these requirements? (Choose two.)

• A. snmp-server host 192.168.101.1 version 3 auth community1 memory
• B. snmp-server enable traps memory bufferpeak
• C. snmp-server host 192.168.101.1 version 2c community1 memory
• D. snmp-server host 192.168.101.1 version 1 community1 auth memory
• E. snmp-server enable snmp-traps community1 bufferpeak

Answer: AB

NEW QUESTION 7
Refer to the exhibit.
router(config)# route-map blackhole-trigger router(config-route-map)# match tag 777 router(config-route-map)# set ip next-hop 10.0.1.1 router(config-route-map)# set origin igp router{config-route-map)# set community no-export
EIGRP is running across the core to exchange internal routes, and each router maintains iBGP adjacency with the other routers on the network. An operator has configured static routes on the edge routers R1 and R2 for IP address 10.0.1.1, which is used as a black hole route as shown. Which configuration should the operator implement to the management router to create a route map that will redistribute tagged static routes into BGP and create a static route to blackhole traffic with tag 777 that is destined to the server at 192.168.10.100?

• A. router(config)# router bgp 55100router(config-router)# redistribute static route-map blackhole-trigger router(config)# ip route 10.0.1.1 255.255.255.255 Null0 tag 777
• B. router(config)# router bgp 55100router(config-router)# redistribute static route-map blackhole-trigger router(config)# ip route 192.168.10.100 255.255.255.255 Null0 tag 777
• C. router(config)# router bgp 55100 router(config-router)# redistribute connectedrouter(config)# ip route 192.168.10.100 255.255.255.255 tag 777
• D. router(config)# router bgp 55100router(config-router)# redistribute connected route-map blackhole-trigger router(config)# ip route 192.168.10.100 255.255.255.255 Null0 tag 777

Answer: B

NEW QUESTION 8
When configuring traffic engineering tunnels in Cisco MPLS core network, you see the traffic is not taking the expected path in the core.
Which command do you use to quickly check path of a TE tunnel?

• A. Traceroute mpls ipv4 -tunnel destination
• B. Ping <tunnel destination IP>
• C. show mpls traffic-engineering tunnels
• D. traceroute <tunnel destination IP>

Answer: A

NEW QUESTION 9
What is a primary benefit of IPoATM or MPLS over ATM backbone service provider networks?

• A. dedicated circuits
• B. variable-length packets
• C. isochronous system
• D. fixed-length cells

Answer: A

NEW QUESTION 10
Refer to the exhibit.

Tier 2 ISP A on AS 653 is connected to two Tier 1 ISPs on AS 321 and AS 51 respectively. The network architect at ISP A is planning traffic flow inside the network to provide predictable network services. Cisco Express Forwarding is disabled on the edge router. How should the architect implement BGP to direct all traffic via the Tier 1 ISP with next-hop 7.4.5.2?

• A. Implement the BGP routing protocol and run the bgp deterministic-med command.
• B. Implement MP-BGP with a 4-byte AS number with the bgp best path compare-routerid command.
• C. Implement the BGP routing protocol and the maximum-paths 2 configuration.
• D. Implement BGP route-reflector functionality with the bgp always-compare-med configuration.

Answer: A

NEW QUESTION 11
Refer to the exhibit:

A network engineer is implementing an OSPF configuration Based on the output, which statement is true?

• A. In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.
• B. OSPFv3 does not run for IPv4 on FastEthemet0/0 until IPv6 routing is enabled on the router and IPv6 isenabled on interface Fastfc.thernet0/0
• C. OSPFv3 cannot be configured for IPv4; OSPFv3 works only for IPv6.
• D. IPv6 routing not enabled" is just an informational message and OSPFv3 runs for IPv4 on interface FastEthernet0/0 anyway

Answer: B

NEW QUESTION 12
An network engineer is deploying VRF on ASBR router R1. The interface must have connectivity over an MPLS VPN inter-AS Option AB network. Which configuration must the engineer apply on the router to accomplish this task?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: D

NEW QUESTION 13
Refer to the exhibit.

A network engineer with an employee id: 3812:12:993 has started to configure router R1 for IS-IS as shown. Which additional configuration must be applied to configure the IS-IS instance to advertise only network prefixes associated to passive interfaces?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: A

NEW QUESTION 14
Refer to the exhibit.

Router 4 is added to the network and must be in the same area as router 1. Which NET should the engineer assign?

• A. 49.0001.0000.0000.0004.00
• B. 49.0111.0000.0000.0001.00
• C. 49.0011.0000.0000.0003.00
• D. 49.0011.0000.0000.0002.00

Answer: C

NEW QUESTION 15
Refer to the exhibit.

An engineer ran this show telemetry command to view subscription SUB11 on RouterX. The engineer then decided that RouterY should provide the same output lor sensor group SGroup13 as RouterX. The engineer cannot access RouterX to copy its configuration No access lists on the router block user access Which configuration must the engineer apply on RouterY to provide the same output from the show telemetry command?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: C

NEW QUESTION 16
Which action does the ingress VTEP perform on traffic between EVPN VXLAN overlays?

• A. routing and tunneling when doing symmetric IRB
• B. routing when doing asymmetric IRB
• C. routing and bridging when doing asymmetric IRB
• D. bridging when doing symmetric IRB

Answer: C

Explanation:

https://www.cisco.com/c/en/us/products/collateral/switches/nexus-9000-series-switches/guide-c07-734107.html

NEW QUESTION 17
......